TM 10-5410-221-24
disassemble observing detail A and the following.
10-12.
Water Box Assembly
(a) Remove screw (64), handle bar (65). Remove
screw (66) and remove hand bail (67) from lock.
a. General. The water box assembly is a metal faced
Remove spacer (69) from handle bail (67) and remove
honeycomb core box assembly housing water system
plate (68).
and electrical system components.
(b) Remove keeper (70) and stop arm (71). Remove
b. Disassembly. Disassemble the water box assembly
screw (72) and remove idle block (73), stop arm (74),
as required to replace damaged components according
keeper (75) an locking blade (76).
to sequence of index numbers assigned to figure 10-10
d. Repair. Repair damage to honeycomb panel using
and observing the following.
procedures outlined in paragraph 2-24. If possible,
(1) Remove all plumbing system components per
straighten any bent plate latches, angles, or extrusions
using plier hammer, vise or other suitable tool.
(2) Remove electrical system components as outlined
e. Overhaul.
Overhaul the door fixed en panel
in chapter 6, section II.
assembly as required to return to a serviceable condition
(3) Remove screw (1, fig. 10-10), washer (2) and
per chapter 10, section II
remove cover assembly (3).
f.
Assembly. Assemble the door fixed en panel in
(4) Separate hinge (5) from cover assembly (3) by
reverse order of disassembly using figure 10-9 as guide
removing rivet (4). Remove seals (6, 7, 8) by peeling
and observing the following.
from cemented area per paragraph 2-20d.
(1) Cement all seals in position using the one part
(5) Remove rivets (9), door assembly (10) and remove
adhesive from the repair kit Clean all old adhesive
seals (11, 12, 13, 14) by peeling from cemented area per
residue from the bone ing area using an approved
cleaning solvent
(6) Remove rivet (15), door assembly (16) and remove
(2) Replace all rivets per paragraph 2-22c.
seals (17, 18, 19, 20) by peeling from cemented area per
(3) Seal all cracks around hinge edge using PRC 611,
Products Research Co., Bu bank, California, or
(7) Remove pin (21) and remove fastener stud (22)
equivalent.
from cover assembly (3).
g. Installation. Install the door fixed en panel in
(8) Remove rivet (23) and remove cover assembly (24).
reverse order of removal using figure 10-9 as a guide
Remove hinge (26) by removing rivet (25).
and observing the follow ing.
(9) Remove pin (27) and remove fastener stud (28)
from cover assembly (24). Remove rivet (29) and
remove receptacle (30).
(Located in back of manual)
(10) Remove seals (31) and insulation (32) by peeling
(1) Position fixed end panel on the shelter and secure
from cemented area per para-graph 2-20d.
hinges per paragraph 10-6 ,
(11) Remove bolts (33), washers (34) and remove
(2) Install angle (2, fig. 10-9) and so cure with rivets
receptacles mounting bracket (35).
(1).
(12) Remove bolts (36), washers (37) and remove
(3) Install ground straps between fixed end and folding
receptacle mounting bracket (38).
end panel assemblies.
(13) Remove rivet (39) to remove receptacle (40) from
(4) Replace electrical wiring in door fixed end panel per
bracket (38). Remove rivet (41) and nut plate (42).
(14) Remove insulation (43) by peeling
(5) Install distribution box assembly per para 6-32.
from
cemented
area
per
(6) Install gusset assembly and secure with bolts and
washers per paragraph 10-10t
10-22
