TM 10-5410-221-24
moving screw (3). Remove screw (5) and re-move shear
(1) Lower roof assembly into proper position
plate (6).
assuring that all gusset and lift ring bolt holes in panel
(2) Remove bolt (7), washer (8) and remove
align with those in fixed end panels.
mobilizer bracket (9).
(2) Secure fixed roof panel by placing gusset
(3) Remove electrical raceway cover (11) by
(8, fig. 10-8) into position and securing with bolts (5) and
removing rivets (10).
washers (6, 7). Replace bolts (1) and washers (2, 3) into
(4) Remove rivet (12) and remove the level
end panel portion of lift ring assembly (4) and tighten
indicators from end panel.
securely.
(5) Remove rivets (14) and instruction plate
(3) Replace bolts into the ceiling mount
(15) from access door.
flanges on the distribution box and tighten securely.
(6) Remove rivets (16) and identification plate
(4) Replace hinge pins and seal assemblies
(17) from end panel.
per paragraph 10-7b.
(7) Remove rivets (18) and remove doubler
(5) Remove fixed end jack assemblies per
plate (19) from panel.
paragraph-,40a.
(8) Remove gutter (21) by removing rivets
(6) Replace all electrical wiring in roof panel
(20).
per chapter 6, section II, table 6-1, figures 6-1 through 6-
(9) Remove outlet panel assembly (25), from
21.
shelter end panel by removing screws (22) and washers
(23, 24).
(10) Remove screws (26), cover (27) and
receptacle box (28) from panel.
(11) Remove screws (29), cover (30) and
a. General. The door fixed end panel assembly is
switch box (31) from panel.
a metal faced honeycomb core panel which houses the
(12) Remove sterilize vent (32) and cap (33) by
access door assembly.
pushing from outside facing of panel with a fiber or soft
b. Removal. Remove the door fixed end panel as
metal punch.
required to replace damaged components using figure
(13) Remove seal (34) from bottom open-ing in
edge extrusion.
(1) Remove gusset assembly from fixed roof
(14) Remove seal (35) by peeling from
and door fixed end panel per paragraph
cemented area per paragraph 2-20d.
10-10b.
(15) Remove nut (36), screw (37), and screw
(2) Remove distribution box from wall per
(38). Remove brace (39). Remove bolt (40) and remove
doubler (41) and angle (42).
(3) Remove electrical wiring from door fixed
(16) Remove handbook container (45) from
end panel per chapter 6, section II.
door assembly by removing rivet (44).
(4) Remove grounding straps from door fixed
(17) Remove rivet (46), hinge (47) and spacer
end panel.
(48). Remove door assembly from end panel.
(5) Remove rivets (1, fig. 10-9) and angle (2)
(18) Remove rivets (49, 50) and remove tees
from bottom edge of panel.
(51, 53) from door. Remove seals (52, 54) from tees
(6) Remove hinges from door fixed end panel
(51, 53) by peeling from cemented areas per paragraph
per paragraph 10-6b and remove door fixed end panel
2-20d.
from shelter.
(19) Remove rivets(57) and remove angles
c. Disassembly. Disassemble the door fixed
(58, 59) from door edge. Remove close-outs (55, 56)
panel assembly as required to replace damaged parts
from edge of door by running a knive or other suitable
according to sequence of index numbers assigned to
tool between closeout and door edge.
(20) Remove doubler (61) from door by
(1) Remove latch assembly (4) by re-
removing rivet (60).
(21) Remove nut (62) and screw (63); remove
the door lock assembly from door and
10-19
