TM 10-5410-221-24
1
Screw (2)
13 Hinge half, folding panel
25
Angle
2
Washer (2)
14 Rivet (58)
26
Closeout
3
Rivet (28)
15 Thermal strip
27
Rivet (42)
4
Screw (2)
16 Seal, bulb and tail
28
Angle
5
Washer (2)
17 Screw (2)
29
Seal
6
Rivet (26)
18 Blind nut (2)
30
Closeout
7
Rivet (24)
19 Hinge assembly
31
Rivet (22)
8
Screw (4)
20 Rivnut (2)
32
Rivet (22)
9
Blind nut (4)
21 Screw (2)
33
Angle
10
Closeout
22 Washer (2)
34
Closeout
11
Hinge pin
23 Ground rod
35
Panel assembly
12
Hinge half, fixed panel
24 Rivet (36)
Figure 10-4--Continued.
(4) Remove screw (14) to remove hinge
assembly (16). Remove blind nut (15) from panel by
a. General.
The folding end panels are a
drilling.
aluminum faced honeycomb core pane equipped with a
(5) Remove rivet (17) and angle (18) from top
removable insert panel for use when attaching to an
edge of panel. Remove closeout (19) using procedure
adjacent shelter, b means of a bellows adapter (fig. 10-
given in step (2) above.
(6) Remove rivnut (20) from panel by drilling
b. Removal. Remove the folding end panel as
out with a drill having a drill bit the same diameter as the
follows.
rivnut.
(1) Disengage all latches and hardware which
(7) Remove screw (21), washer (22), and
secures the folding end panels to th folding floor panel
remove ground rod (23) from panel.
and observing the procedures given on the shelter
(8) Remove angle (26) by removing rivets
instruction plat located on the access door.
(25).
(2) Remove the grounding straps between
(9) Remove seal (27) by peeling from
the fixed end panels and folding en panels, and between
cemented area using procedure given in para 2-20d.
the folding side pane and folding end panel.
(10) Remove closeout (28) per step (2) above.
(3) Remove the screws (1, fig. 10-5) washers
(11) Remove rivet (29, 30) and remove tee
(2) and rivets (3) which secure th hinges to the fixed end
(31).
panel and the folding side panels and remove the folding
(12) Remove bulb and tail seal (32) by peeling
end panel
from cemented area on tee (31) per paragraph 2-20d.
c. Disassembly.
Disassemble the end pane
Remove closeout (33) from panel edge. Remove blind
assemblies as required to replace damage( components
nut (34) from panel.
according to sequence of index numbers assigned to
(13) Remove screw (35) and remove right
figure 10-) and observing the following.
hand and left hand adapter frames (37, 38) from panel.
(1) Remove rivets (4), screws (5) an/ remove
Remove rivnut (36) by drilling using same size drill bit as
hinge assembly (9) from panel edge Remove blind nut
rivnut diameter.
(6) and blind nut (8) from panel edge.
(14) Remove rivet (39) and remove angle (40),
(2) Remove closeout (10) by sliding a knife or
closeout (41), angle (42) and closeout (43) from bottom
other sharp tool between closeout and panel core.
edge of panel.
(3) Remove bulb and tail seal (11) from
(15) Remove box (44) from panel by running a
thermal strip (13).
Remove thermal strip (13) by
knife around edges to break adhesive bond between
removing rivets (12).
core and box (44).
(16) Remove rivets (29, 30) to remove upper
tee (45). Remove bulb and tail sea! (46) by peeling from
cemented area per para-graph 2-20d.
10-9
