TM 10-5410-221-24
to the folding end panels. Lift up the folding roof panel
(17) Remove rivets (36, 37) and remove shim
and support roof using the adjustable roof support;
(38) and latch assembly (39) from the panel.
remove the side panel assemblies.
(18) Remove latch assembly (41) from panel
c. Disassembly. Disassemble the side pan' as
by removing rivets (40).
required to replace damaged parts according to
(19) Remove alignment plate (43) from panel
sequence of numbers assigned to figure 10-3 and
by removing rivets (42).
observing the following.
(20) Remove right hand adapter frame (46)
(1) Remove screws (3, fig. 10-3), washers
and left hand adapter frame (47) from panel by removing
(4), rivets (6) and screws (7) and remove hinge assembly
screws (44). Remove rivnut (45) from panel by drilling
from panel edge. Remove hinge pin (.10) by pulling in a
using a drill bit with the same diameter as the rivnut.
straight ;if using pliers or other suitable tool to grip t pin.
(21) Remove tee (50) by removing rivets (48,
Separate hinge half (11) from hinge half (12).
49).
(2) Remove insert (8) using procedure
(22) Remove bulb and tail seal (51) by peeling
outlined in paragraph 2-23a.
from cemented area on tee (50).
(3) Remove rivets (13) which secure angles
(23) Remove closeout (52) per paragraph 10-
(14) to side panel.
4, c(4).
(4) Remove closeouts (15) by sliding sharp
(24) Remove rivet (53) and remove latch and
knife or other suitable tool between closeout and
box assembly from panel. Remove rivet (54) and
honeycomb paper core using ca: not to damage panel or
separate latch (55) from latch box (56).
honeycomb core.
(25) Remove rivet (57) to remove angle (58)
(5) Remove screw (16), washer (1I and
from panel bottom edge.
ground rod (18) from panel.
(26) Remove closeout (59) per paragraph 10-
(6) Remove rivnut (19) from panel l drilling
4, c(4).
d. Repair. Repair damage to honeycomb core
using a drill bit with the same diameter as the rivnut.
panel assemblies using procedures de-scribed in
(7) Remove rivnut (20) which secure the top
angles (21) to the panel top edge
procedures described in paragraph 2-22. If possible,
(8) Remove closeout (22) using procedure
straighten any bent plates, tees, angles or latches.
given in step c(4), above.
Repair dam-aged closeouts per paragraph 2-25.
(9) Remove tee (25) by removing rive (24).
e. Overhaul. Overhaul the side panel assemblies
(10) Remove bulb and tail seal (26) b peeling
from cemented area on tee (25) pre paragraph 2-20d.
(60, 61, fig. 10-3) as required to return to a serviceable
(11) Remove bulb seal (27) by peeling from
condition per chapter 10, section III.
f. Assembly.
Assemble the side panel
cemented area on tee (25).
(12) Remove closeout (28) using procedure
assemblies in reverse order of disassembly using figure
given in paragraph 10-4e (4).
(13) Remove tee (31) by removing rivet (29,
(1) Install all blind nuts and rivnuts using
30).
installation
procedures
recommended
by
the
(14) Remove bulb and tail seal (32) b peeling
manufacturer.
from cemented area on tee (31) per paragraph 2-20d.
(2) Replace all rivets observing procedures
(15) Remove closeout (33) per para 10-4, c(4).
outlined in paragraph 2-22c.
(16) Remove ball lock receptacles (35 from
(Located in back of manual)
panel by removing rivet (34).
10-6
