TM 10-5410-221-24
(17) The removable panel assembly (61 shall
tioned air distribution plenums and conditioned air duct
be removed from the end panel (47) b removing screws
adapters (fig. 10-1).
b. Removal. Remove the folding roof panel
(48), washers (49), an lockwashers (50) and pulling
panel (61 away from end panel assembly (47).
assembly as follows.
(18) Remove strap(52) by removing rivets (51).
(1) Disconnect wiring harness assemblies
(19) Remove closeout (53, 60) per step
at the J21 and J22 receptacle boxes per paragraph 6-
(2) above.
(20) Remove screw (55), washer (56 and
(2) Disengage all latches which secure the
remove ground rod (57). Remove rivnut (54) by drilling
roof to the end and side panels.
out with a drill having a drill bit the same diameter as the
(3) Place folding end and folding side panels
rivnut.
in the folded position.
(21) Remove handle assembly (59) b removing
(4) Lower folding roof to gain access to the
rivets (58).
hinge assemblies which secure the fold-ing roof to the
d.
Repair. Repair damage to honeycomb panel
fixed roof.
using procedures outlined in paragraph 2-25. If possible
(5) Remove the rivets (1, fig. 10-6) which
straighten any bent plate, latches, angles or tees. Repair
secure the retainer strip (2) and seal (3) to the hinge
damaged close outs per paragraph 2-25e.
halves and remove the seal (3).
e.
Overhaul. Overhaul the folding en panels as
(6) Remove the hinge pin (4) to separate the
hinge halves and remove the panel assembly.
required to return to a serviceable condition per chapter
c. Disassembly. Disassembly the folding roof
f. Assembly. .Assemble the folding en panel
panel as required to replace damaged parts using figure
assemblies in reverse order of disassembly using figure
(1) Remove gasket retainers (6, 7, 8, 9) by
removing rivets (5). Slide bulb seal (10, detail B) from
(1) Install blind nuts
and rivnuts per
groove in gasket retainers.
manufacturer's recommended procedures.
(2) Remove strike assembly (12) by re-
(2) Replace rivets observing procedure given
moving bolt (11).
(3) Remove rivet (13) and remove retainer
(3) Seal all cracks around hinge edge using
strip (14) and seal (15) from panel edge.
sealant PRC 611, Products Research Co Burbank,
(4) Remove ball lock receptacle (17) by
California, or equivalent.
removing rivet (16).
(4) Cement seals using procedures out lined
(5) Remove pin (62) from pivot assembly (20)
g. Installation. Install panel assemblies i reverse
and remove support assembly (66).
(6) Remove bolt (18), washer (19) and
order of removal using figure 10-5 a guide and referring
remove pivot assembly (20) from edge of extrusion (22).
to instruction plate o shelter door for procedures on
(7) Remove rivet (21) and remove extrusion
securing th end panel assembly to floor and folding side
(22, 30) from panel edge.
panels.
(8) Separate shear angle (27) from extrusion
(30) by removing bolt (23), washer (24), bolt (25) and
Folding Roof Panel Assemblies Repair
washer (26). Remove rivet (28) to remove spacer (29).
a. General. The folding roof panel assemblies
(9) Remove screw (31), washer (32) and
are aluminum faced honeycomb core panels. There are
ground rod (33) from panel.
two folding roof panels one on each end of the shelter.
The folding roof panels provide for attachment of the
condi
10-10
