TM 10-5410-223-14/1
C1
aluminum faced honeycomb core panel. The fixed
(8) Remove threshold (24, fig. 6-8, sheet 1 of 2)
floor panel assembly provides mounting for the
by drilling out and removing rivets (23). Lift out side
multipurpose shelter, skid assembly.
panel assemblies (66).
b. Removal. Remove the fixed floor assembly as
c. Disassembly. Disassemble the end panel
required to replace damaged components using
assembly as required to replace damaged parts
figure 6-9 as a
guide and
observing the
following:
according to sequence of index numbers assigned in
(1) Remove the folding roof panel as described
following:
(1) Remove jack (13, fig. 6-8, sheet 1 of 2) by
manner.
removing screws (10), washers (9), screws (73),
(2) Remove the fixed roof panel as described in
washers (75), and nuts (74).
(2) Remove jack stowage assembly (62, fig. 6-
(3) Remove the fixed side and fixed end panels
8, sheet 2 of 2) by removing screw (60) and washer
(61). Remove quick release pin (61A).
(4) With other panels removed the floor panel
(3) Remove level assembly (43) by removing
can be raised and positioned for disassembly.
Screws (44).
c. Disassembly. Disassemble the fixed floor panel
(4) Remove tow cable attachment bracket (53)
as required to replace damaged parts according to
by removing screws (46) and screws (52).
sequence of index numbers assigned in figure 6-9 and
(5) Remove mobilizer attachment plate (63) by
observing the following:
removing screws (56) and washers (64).
(1) Remove channel (13) and doubler (11) by
(6) Remove mobilizer attachment plate (40) by
removing bolts (12).
removing screws (45) and screws (48).
(2) Remove tiedown ring (16) from channel (13)
(7) Remove latch assembly (49) from mobilizer
by removing bolts (14).
attachment plate (40) by removing screws (50).
(3) Remove nut plate (26) from channel (13) by
(8) Remove cargo tiedown (58) by loosening
drilling out and removing rivets (17).
screws (57).
(4) Remove skid assembly (36) by drilling out
(9) Remove door latch riser (65) and guide (67)
and removing rivets (23).
by removing screw (69).
(5) Remove rub assembly (37) and rein-
(10) Remove link-latch stake and spacer by
forcement plate (28) from skid (36) by drilling out
drilling out and removing rivets.
and removing rivets (24).
(6) Remove tiedown ring (34) from skid (36) by
removing bolts (33).
sheet 1 of 2) from sill (30) by removing screws (6).
(12) Remove filler plate (34, fig. 6-8, sheet 2 of
(7) Remove nut plate (31) from skid (36) by
2) and closeout (32) from sill panel (30) by drilling
drilling out and removing rivets (35).
out and removing rivets (38).
(8) Remove end closeout (20) from skid (36) by
d. Repair. Repair damage to honeycomb panel. If
removing bolts (18) and washers (19).
possible, straighten any bent plates, latches, angles
(9) Remove plug assembly (41) by prying loose
and extrusions using haremer, pliers, vise or similar
epoxy seal.
tools. Replace irreparable parts.
(10) Remove valve assembly (5) by drilling out
e. Assembly. Assemble the end panel in reverse
and removing rivets (4).
order of disassembly using figure 6-8 (sheets 1 and 2)
(11) Remove plate (25) by drilling out and
as a guide and observing the following:
removing rivets (24).
(1) Install all rivets.
(12) Remove support plates (31 and 11) by
(2) Replace all potted inserts, as necessary.
removing screws (30).
(3) Seal all joints with sealant EC 776, 3M Co.,
(13) Separate plate (10) from plate (31) by
or equivalent.
drilling out and removing rivets (9).
f. Installation. Install the end panel assembly in
(14) Remove hinge strip (43) and seal (42) by
reverse order of removal using figure 6-8 (sheets 1
drilling out and removing rivet (44).
and 2) as a guide and observing the following:
(15) Remove hinge half (3) by drilling out and
(1) Adjust sight level assembly (41, 42 and 43,
removing rivets (7).
(16) Remove closeout extrusions (1) by drilling
(2) With folding roof and floor panels in closed
out and removing rivets (6 and 9), then by prying
position, adjust folding panel latches (49) by means
loose from panel (38).
of adjusting screw accessible from outboard end of
d. Repair. Repair damage to honeycomb panel
latch to ensure tight closure of folding panels.
structure. If possible, straighten any bent plates,
latches, angles and extrusions using hammer, pliers,
6-9. Fixed Floor Panel Assembly Repair
Vise or similar tool. Replace irreparable parts.
a. General. The fixed floor panel assembly is an
Change 1, 6-33