TM 10-5410-223-14/1
C1
b. Removal. Remove the side panel assembly as
c. Duct Port Disassembly. Disassemble the roof
required to replace damaged components using
duct port as follows:
figure 6-7 as a
guide and
observing the
following:
(1) Remove grounding strap (35, fig. 6-6, sheet
(1) Remove the folding roof assembly.
1 of 2) by removing screw (37) and washers (34 and
(2) Remove t h e f i x e d r o o f a s s e m b l y a s
36).
(2) Remove hinge (30) by drilling out and
removing rivets (39).
removing screws (11 and 12).
(3) Remove cover (38) and flange assembly (8)
(4) Remove tension plate (20) by removing
by loosening latches (11).
screws (21 ) and rivets (22).
(4) Remove latch strike (29) from cover (38) by
(5) Lift out door sill assembly (5, 8 and 9).
drilling out and removing rivets (28).
(6) Remove plate (23) by drilling out and
(5) Remove latch strike (31) from cover (38) by
removing rivets (45).
drilling out and removing rivets (27).
(7) Remove side panels (1) by drilling out and
(6) Remove duct port angle ring (13) by drilling
removing rivets (41) in side bracket (42), also rivets
out and removing rivets (12).
(44) in base brackets (43).
d. Repair. Repair damage to honeycomb panel. If
c. Disassembly. Disassemble the side panel
possible, straighten any bent plates, latches, angles
assembly as required to replace damaged parts
and extrusions using hammer, pliers, vise or similar
according to sequence of index numbers assigned in
tool. Replace defective parts that are irreparable.
e. Overhaul. Overhaul the roof assembly as
(1) Remove folding steps (35) by removing
required to return to serviceable condition as per
bolts (33) and washers (34).
Section III.
(2) Remove level assembly (19) by removing
f. Assembly. Assemble the roof panel in reverse
screws (18).
order of disassembly using figure 6-6 (sheets 1 and 2)
(3) Remove drip cap assembly (4, fig. 6-8, sheet
as a guide and observing the following:
1 of 2) from door sill (5, fig. 6-7) by removing screws
(1) Install all rivets.
(2) Replace all potted inserts.
(4) Remove plate (9, fig. 6-7) and closeout (8)
(3) Seal all joints with sealant EC 776, 3M Co.,
from door sill (5) by drilling out and removing rivets
or equivalent.
(13).
(4) Install handle assembly (41, fig. 6-6, sheet 1
(5) Remove all airlock clamps (25) around door
of 2) positioned so that spring return closes handle in
frame by loosening nut (26) and removing screw (27)
direction away from nearest edge of roof panel.
and spacer (24).
g. Installation. Install the roof panel assembly in
(6) Remove filler plate (36) and extrusion
reverse order of removal using figure 6-6 (sheets 1
closeout (37) from side panels (1) by drilling out and
and 2) as a guide and observing the following:
removing rivets (39).
(1) Install hinge half (5, fig. 6-6, sheet 1 of 2)
(7) Remove rub strips (29) by drilling out and
and bracket assemblies (42, fig. 6-6, sheet 2 of 2)
removing rivets (28).
before placing roof assembly on shelter.
d. Repair. Repair damage to honeycomb panel. If
(2) Because of the weight of the roof assembly,
possible, straighten any bent plates, latches, angles
four men, one at each comer, are required to lift it
and extrusions using hammer, pliers, vise or similar
back onto the shelter.
tools. Replace irreparable parts.
(3) In installing latches (11, fig. 6-6, sheet 1 of
2), observe that four latches point upward to mate
e. Overhaul. Overhaul the side panel assembly as
required to restore to serviceable condition using the
with strikes (31 ), the other four point downward.
methods given in Section III.
6-7. Side Panel Assembly Repair
f. Assembly. Assemble the side panel in reverse
a. General. There is only one side panel assembly
order of disassembly using figure 6-7 as a guide and
on the multipurpose shelter. The folding roof and
observing the following:
folding floor panels constitute the other side. Space
(1) Install all rivets.
is provided in the side panel for mounting a folding
(2) Replace all potted inserts.
door or a removable door panel. The side panel
(3) Seal all joints with sealant EC 776, 3M Co.,
or equivalent.
aluminum faced honeycomb core panels fastened to
(4) Install folding steps (35) position to hinge
the multipurpose shelter, roof, floor and end panels,
upward in closing.
and joined by a connecting sill panel across the top of
g. Installation.
the door opening.
(1) Install the side panel assembly in reverse
6-30