TM 10-5410-223-14/1
(14) Install the plate assembly (34) and secure
e. Overhaul. overhaul the door assemblies as
with rivets (33).
required to return to serviceable condition as per
(15) Install seals (29 and 32) and seal retaining
Section III.
strips (28 and 31) and secure with rivets (27 and 30).
f. Assembly.
(16) Install the doubler (26, fig. 6-5, sheet 2 of
(1) Install closeouts (81 and 82, fig. 6-5, sheet 5
5) and secure with rivets (25).
of 5) onto the raw door panels (83).
(17) Install the door stop (24) and secure with
(2) Install hinges (79, fig. 6-5, sheet 4 of 5) and
screws (23).
secure with rivets (78).
(18) Install the half hinges (20 and 21) and
(3) Install gaskets (75, 76 and 77) and housing
assembly (74), secure with screws (73).
springs (22) and secure with pin (19).
(19) Install inserts (18), if removed.
(4) Install the support (71) onto the plate (72)
(20) Install the hinge assembly (17) and secure
and secure with rivets (70).
with rivets (16) and screws (15).
(5) Install the LH and RH hinges (68 and 69)
(21) Install closeouts (14), spacer (13), windows
and secure with rivets (67).
(6) Install the counterweight (66) and secure
(12) and outer frame (11), secure with rivets (10).
(22) Install the pile fasteners (8 and 9) and inner
with screw (65) and nut (64).
frame (7) and secure with rivets (6).
(7) Install the damper assembly (63) and secure
with washers (62), pins (61) and cotter pins (60).
(23) Install the hook fasteners (4 and 5) using
adhesive.
(8) Install the cover plate (59).
(24) Install the blackout curtain (3) and strip
(9) Install the handle (58, fig. 6-5, sheet 3 of 5)
(2) and secure with rivets (1).
and secure with washers (57), screws (56) and rivets
g. Installation.
(55).
(10) Install nuts (54), if removed, then install
NOTE
plate (53), coupling (52), plate (51), plates (49 and
Installation procedures listed below are appropriate
50) and lock assembly (48), secure with washers (47)
for both door assemblies,
and screws (46).
(1) Position the door panel, figure 6-4 (sheet 3
(11) Install bars (45) and handle (44) and secure
of 3), onto the shelter wall.
with cotter pins (43).
(2) Swing door outward, figure 6-4 (sheet 2 of
(12) Install nuts (42), if removed, then install
3), and install mounting screws.
risers (41 ) and guides (40) and secure with washers
(3) Swing door inward, figure 6-4 (sheet 1 of 3),
(39) and screws (38).
and install mounting screws.
(13) Install nuts (37), if removed, then install
striker (36) and secure with screws (35).
Section II. FIXED FLOORS, WALLS AND CEILING
(4) Remove rivets (30, fig. 6-7) and screws (31)
6-5. General
in upper tension plates (32).
This section provides i n s t r u c t i o n for the
(5) Drill out all rivets (53, fig. 6-6, sheet 2 of 2)
replacement of those items considered as being fixed
around perimeter of roof panel assembly.
panel assemblies. The fixed panel assemblies are the
(6) Remove wall panel screws (52) from angle
roof panel, the side panel, the end panels and the
bracket (56).
floor.
(7) Using one man at each inside corner, raise
6-6. Roof Panel Assembly
off the roof panel assembly,
a. General,
The roof panel assembly is an
(8) Remove hinge half (5, fig, 6-6, sheet 1 of 2)
aluminum faced honeycomb core panel.
by drilling out and removing rivets (6 and 7).
b. Removal and Disassembly,
(9) Remove lift rings (26) by removing bolts
(1) Refer to paragraph 6-2 and remove the
(33).
folding roof assembly,
(10) Remove handle (41) by drilling out and
(2) Remove lift rings and plate (26, fig. 6-6,
removing rivets (40).
sheet 1 of 2) by removing bolts (33).
(11) Remove clamps (16) by removing screw
(3) Remove screws (11 and 12, fig. 6-7) and
(19), washer (18) and spacer (17).
screws (36 and 37, fig. 6-8, Sheet 1 of 2) in doubler
(12) Remove brackets (42, fig, 6-6, sheet 2 of 2)
plates.
by removing screws (52).
6-22
