TM 10-5410-223-14/1
C1
KEY to Figure 6-2 2
Bracket assemblies
32.
23. Screws
Snap fasteners
33.
24. Rivets
Nuts
34.
25. Half hinge
Bolts
35.
26. Closeout
Washers
36.
27. Rivets
Angles
37.
28. Rivets
Inserts
38.
29. Bracket assemblies
Deep draw cans
39.
30. Rivets
*40.
Screws
31. Rivets
Safety hasp
**41.
42.
Raw panel
*Installed on shelter serial No. 630 thru 727 only.
g. Installation.
c. Inspection.
(1) Using a suitable lifting device position the
(1) Inspect all parts for wear and damage.
folding roof assembly (2, fig. 6-1).
(2) Inspect the raw panel for cracks, breaks,
(2) Secure the folding roof assembly (2) by
dents and holes.
installing hinge (1).
d. Repair.
(1) Replace worn and damaged parts.
6-3. Folding Floor Assembly
(2) repair damaged roof accordingly.
a. Removal. Remove the folding floor assembly
e. Overhaul. Overhaul the folding roof assembly
using the same procedure as those used for removing
as required to return to serviceable condition as per
the folding roof assembly.
Section III.
b. Disassembly.
f. Assembly.
(1) Remove screws (1, fig. 6-3, sheet 1 of 2) and
(1) On serial No. 630 thru 727 only. Install
rivets (2) and remove the half hinge (3) and closeout
safety hasp (41, fig. 6-2, sheet 2 of 2) and secure
(4).
with screws (40).
(2) Remove screws (5) and washers (6) and
(2) Install the deep draw cans (39) into the raw
remove the strikes (7).
panel (40), if removed.
(3) Remove bolts (8) and washers (9) and
(3) Install all inserts (38) accordingly.
remove the angles (10).
(4) Install the angles (37) and secure with
(4) Remove inserts (11), if damaged.
washers (36) and bolts (35).
(5) Remove the deep draw cans (12), if
(5) Install nuts (34) and snap fasteners (33).
damaged.
(6) Install bracket assemblies (32) and secure
(6) Remove screws (12, fig. 6-3, sheet 2 of 2)
by installing rivets (30 and 31) accordingly.
and washers (14) and remove the level assembly (15).
(7) Install bracket assemblies (29) and secure
(7) Remove cups (16) and remove the vial (17)
by installing rivets (27 and 28).
from bracket (18).
(8) Install the closeout (26) and half hinge (25)
(8) Remove nut (19) and box (20).
and secure with rivets (24) and screws (23).
(9) Remove rivets (21) and remove rubber strips
(9) Install channels (22, fig. 6-2, sheet 1 of 2)
(22).
and extrusions (21) and secure with rivets (20).
(10) Remove bolts (23) and washers (24) and
(10) Install brackets (19) and secure with
remove angles (25).
washers (18) and bolts (17).
(11) Remove inserts (26), if damaged.
(11) Install seal (16) and plates (15) and secure
(12) Remove inserts (27), if damaged.
with rivets (14).
(13) Remove rivets (28) and remove castings
(12) Install castings (13) and secure with rivets
(29).
(12).
(14) Remove rivets (30 and 32) and remove
(13) Install spacers (10 and 11) and extrusion
extrusions (31 and 33) from the raw panel (34).
(9) and secure with rivets (7 and 8).
(15) On shelter serial No. 630 thru 727 only.
(14) Install strikes (6) and secure with washers
Remove screws (34) and remove hasp staple (35)
(5) and screws (4).
and shim (36).
(15) Install handles (3) and secure with washers
(2) and bolts (1).
Change 1, 6-7
