TM 10-5410-221-24
(4) Remove screws to disconnect electrical
with wiring chart (table 6-2).
leads from CB2, CB6, CB7, CB8, CB9, CB11, CB14, CB-
(2) Replace washers (55, 31), lockwashers
16, CB17, CB18 and CB19 circuit breakers.
(54, 30) and nuts (53, 29) on terminals of terminal
(5) Remove 400 Hertz wiring harness (18) from
boards TB1, TB2, TB3 and TB4 and tighten nuts
distribution box.
securely. Replace terminal board covers (25, 35, 49, 57,
c. Disassembly. Disassemble 400 Hertz wiring
(3) Place circuit breaker panel in position and
secure with screws.
harness as required to replace damaged parts as follows
(1) Remove terminals (1 through 8).
6-25.
Sterilizer Wiring Harness Assemblies
(2) Remove identification strap (9) and tie
straps (10) from harness assembly.
a. General.
The sterilizer wiring harness
(3) Remove any damaged or defective
assemblies consist of a connector and four electrical
electrical leads.
leads to provide interconnection between the electrical
system and two sterilizers, when used.
d. Assembly. Assemble 400 Hertz wiring harness
in reverse order of disassembly using figure 6-24 as a
b. Removal. Remove sterilizer harness assemblies
guide and observing the following.
(5, 6, fig. 6-22) according to sequence of index numbers
(1) Install new wires, if required, and secure
assigned to figure 6-22 and observing the following.
with tie straps (9, fig. 6-24).
(1) Open circuit breaker panel cover (125, fig.
(2) Install terminals (1 through 8) and crimp to
secure.
(2) Remove circuit breaker panel per
paragraph 6-23, b(2).
e. Test. Check continuity of wiring harness using a
(3) Remove terminal board cover (35) and
continuity light, multimeter, or other continuity checking
remove nut (29) lockwasher (30) and washer (31) from
device. Refer to figure 1-'7 and table 6-2 for wiring
terminal 5 on TB3 terminal board (38) for the J5 harness
routing and terminal identification. Continuity must exist
assembly (5) and terminal 4 for the J6 harness assembly
between wire ends. Replace wire if continuity does not
(6) and remove the electrical leads from the terminal
exist between wire ends.
boards.
(4) Remove nuts (1), washers (2) and screws
f. Repair.
Repair 400 Hertz wiring harness
(3) and remove J5 (5) and J6 (6) connectors from
assembly to return to a serviceable condition as follows.
distribution box. Remove cover (4).
(1) Inspect individual wires for cuts and
(5) Remove screws to disconnect the harness
abrasions of insulation. Minor cuts and abrasions are
electrical leads from CB14 circuit breaker for the J5
acceptable and shall be repaired by wrapping damaged
sterilizer harness (5) and CB11 circuit breaker for the J6
area with vinyl tape or other suitable electrical wiring
sterilizer harness (6).
tape. Replace any individual wires which are cut through
(6) Remove the harness assemblies (5, 6) from the
or otherwise damaged.
distribution box.
(2) Inspect tie straps (10, fig. 6-24) for
c. Disassembly.
tightness and fraying. Replace any loose or frayed tie
Disassemble the sterilizer
straps.
harness assemblies as required to replace damaged
parts as follows (fig. 6-25).
g. Installation. Install 400 Hertz wiring harness in
(1) Remove terminals (1, fig. 6-25).
reverse order of removal using figure 6-22 as a guide
(2) Remove cable straps (2) and identification
and figures 1-7 and table 6-2 for terminal location and
strap (3).
identification and observing the following.
(3) Slide back insulation sleeving (4, 5) to
(1) Position harness assembly (18, fig. 6-22) in
expose solder connections at connector (6) and unsolder
distribution box and install electrical leads in accordance
6-43
