TM 10-5410-221-14/1
1. Screw (2)
16. Hinge ay
31. Tee
46.
End panel ay
2. Washer (2)
17. Rivet (34)
32. Seal, bulb and tail
47.
Screw (10)
3. Rivet (25)
18. Angle
33. Closeout
48.
Washer (10
4. Rivet (56)
19. Closeout
34. Blind nut (10)
49.
Lockwasher (10)
5. Screw (2)
20. Rivnut
35. Screw
50.
Rivet(23)
6. Blind nut (2)
21. Screw (2)
36. Rivnut
51.
Strap
7. Screw (4)
22. Washer (2)
37. Adapter frame, R.H.
52.
Closeout
8. Blind nut (4)
23. Ground rod
38. Adapter frame, L.H.
53.
Rivnut
9. Hinge assembly
24. Blind nut
39. Rivet (6)
54.
Screw (2)
* 9A. Seal
25. Rivet (44)
40. Angle
55.
Washer (2)
*9B. Seal
26. Angle
41. Closeout
56.
Ground rod
10. Closeout
27. Seal
42. Angle
57.
Rivet (24)
11. Seal, bulb and tail
28. Closeout
43. Closeout
58.
Handle assembly
12. Rivet (58)
29. Rivet (66)
44. Tee, upper
59.
Closeout
13. Thermal strip
30. Rivet (66)
45. Seal, bulb and tail
60.
Removable panel
14. Screw (2)
15. Blind nut ay (2)
*Installed on shelter serial No. 402 and subsequent.
Figure 8-5 - Continued.
(3) Engage all latches and hardware to secure the
(4) Remove screw (14) to remove hinge assembly
folding end panels to the folding floor panel.
(16). Remove blind nut (15) from panel by drilling.
(5) Remove rivet (17) and angle (18) from top edge
of panel. Remove closeout (19) using procedure given
8-6. Folding End Panels W/Removable Panel
in step (2) above.
(6) Remove rivnut (20) from panel by drilling out
a. General. The folding end panels are an aluminum
with a drill having a drill bit the same diameter as the
faced honeycomb core panel equipped with a removable
rivnut.
insert panel for use when attaching to an adjacent
(7) Remove screw (21), washer (22), and remove
shelter, by means of a bellows adapter (fig. 8-1).
ground rod (23) from panel.
b. Removal. Remove the folding end panels as
(8) Remove angle (26) by removing rivets (25).
follows.
(9) Remove seal (27) by peeling from cemented
(1) Disengage all latches and hardware which
area.
secures the folding end panels to the folding floor panel
(10) Remove closeout (28) per step (2) above.
and observing the procedures given on the shelter
(11) Remove rivet (29 and 30) and remove tee
instruction plate located on the access door.
(31).
(2) Remove the grounding straps between the fixed
(12) Remove bulb and tail seal (32) by peeling from
end panels and folding end panels, and between the
cemented area on tee (31). Remove close-out (33) from
folding side panel and folding end panel.
panel edge. Remove blind nut (34) from panel.
(3) Remove the screws ( , fig. 8-5), washers (2) and
(13) Remove screw (35) and remove right hand and
rivets (3) which secure the hinges to the fixed end panel
left hand adapter frames (37 and 38) from panel.
and the folding side panels and remove the folding end
Remove rivnut (36) by drilling using same size drill bit as
panel.
rivnut diameter.
c. Disassembly.
Disassemble the end panel
(14) Remove rivet (39) and remove angle (40),
assemblies as required to replace damaged components
closeout (41), angle (42) and closeout (43) from bottom
according to sequence of index numbers assigned to
edge of panel.
(15) Remove rivets (29 and 30) to remove upper
(1) Remove rivets (4, fig. 8-5), screws (5) and
tee (44). Remove bulb and tail seal (45) by peeling from
remove hinge assembly (9) from panel edge. Remove
cemented area.
blind nut (6) and blind nut (8) from panel edge.
(16) The removable panel assembly (60) shall be
(1.1) Remove seals (9A and 9B) by peeling from
removed from the end panel (46) by removing screws
cemented area.
(47), washers (48), lockwashers (49) and pulling panel
(2) Remove closeout (10) by sliding a knife or other
(60) away from end panel assembly (46).
sharp tool between closeout and panel core.
(17) Remove strap (51) by removing rivets (50).
(3) Remove bulb and tail seal (11) from thermal
(18) Remove closeout (52 and 59) per step (2)
strip (13). Remove thermal strip (13) by removing rivets
above.
(12).
(19) Remove screw (54), washer (55) and remove
ground rod (56). Remove rivnut (53) by drilling out with
Change 2 8-11
