TM 10-5410-221-14/1
1.
Screw( (2)
10.
Closeout
19.
Hinge assembly
28.
Angle
2.
Washer (2)
11.
Hinge pin
20.
Rivnut(2)
29.
Seal
3.
Rivet (28)
12.
Hinge half, fixed panel
21.
Screw (2)
30.
Rivet (22)
4.
Screw (2)
13.
Hinge half, folding panel
22.
Washer (2)I
31.
Rivet (22)
5.
W(2)
14.
Rivet (58)
23.
Ground rod
32.
Rivet (22)
6.
Rivet (26)
15.
Thermal strip
24.
Rivet ((, )
33.
Angle
7.
Rivet (24)
16.
Seal, bulb and tail
25.
Angle
34.
Closeout
8.
Screw (4)
17.
Screw (2)
26.
Closeout
35.
Panel assembly
9.
Blind nut (4)
18.
Blind nut (2)
27.
Rivet (42)
Figure 8-4--Continued
given on the shelter instruction plate located on the door.
(8) Remove rivets (24) and remove angle (25) from
(4) Install the folding floor jack assemblies.
top edge of panel.
(9) Remove closeout (26) from panel edge by
inserting a knife or other sharp tool between closeout
8-5. Folding End Panel Assemblies
and panel honeycomb core.
(10) Remove rivets (27) and remove angle (28)
a. General. The folding end panels are an aluminum
from panel edge. Remove closeout (30) from panel
faced honeycomb core panel. The shelter is equipped
edge.
with two folding end panels (fig. 8-1).
(11) Remove seal (29) by peeling from cemented
b. Removal.
Remove the folding end panel
area.
assemblies as follows.
(12) Remove rivets (31 and 32) which secure angle
(1) Disengage all latches and hardware which
(33) to panel bottom edge. Remove closeout (34) from
secure the folding end panels to the folding floor panel.
panel assembly (35) bottom edge.'
(2) Remove the grounding straps between the fixed
d. Repair. Repair damage to honeycomb core panel
end panels and folding end panels, and between the
using procedured outlined in paragraph 8-4. If possible,
folding side panel and folding end panel.
straighten any bent plates, angles, or latches. Repair
(3) Remove the screws (1, fig. 8-4) and washers (2)
damaged closeouts per paragraph 8-4.
and rivets (3) which secure the hinge assemblies to the
e. Overhaul. Overhaul the folding end panel as
fixed end panels and the folding side panels and remove
required to return to a serviceable condition per chapter
the folding end panel.
8, section III.
c. Disassembly. Disassemble the folding end panel
f. Assembly.
Assemble the folding end panel
assemblies as required to replace damaged parts
assemblies using figure 8-4 as a guide and observing the
according to sequence of numbers assigned to figure 8-4
following:
and observing the following.
(1) Install blind nuts and rivnuts using
(1) Remove screw (4, fig. 8-4), washer (5) and
manufacturers recommended procedures.
rivets (6) to remove hinge assembly from panel. Remove
(2) Replace rivets.
blind nut (9).
(3) Seal all cracks around hinge half edges with
(2) Remove closeout (10) from panel edge.
sealant EC776, 3M Co., or equivalent.
(3) Remove hinge pin (11) and separate hinge half
(4) Cement seal assemblies.
(12) from hinge half (13).
g. Installation. Refer to shelter instruction plate on the
(4) Remove rivets (14) and remove thermal strip
shelter door for procedures on securing the end panel
(15). Remove bulb and tail seal from thermal strip (15)
assembly to the folding floor and folding side panels.
by peeling from cemented area.
Install the panel assembly as follows:
(5) Remove hinge assembly (19) from panel by
(1) Install the screws (1, fig. 8-4) and washers (2)
removing screws (17). Remove blind nuts (18) from
and rivets (3) to secure the hinge assemblies to the fixed
panel by drilling using a drill bit with a diameter the same
end panels and the folding side panels and install the
size as the blind nut.
folding end panel.
(6) Remove rivnut (20) by drilling using a drill bit
(2) Install the grounding straps between the fixed
having the same diameter as the rivnut.
end panels and folding end panels, and between the
(7) Remove screw (21), washer (22), and remove
folding side panel and folding end panel.
ground rod (23).
8-9
