• Home
  • Download PDF
  • Order CD-ROM
  • Order in Print
LOCATION AND DESCRIPTION OF MAJOR PARTS - Contd. - TM-10-5410-229-13P_19
LOCATION AND DESCRIPTION OF MAJOR PARTS - Contd. - TM-10-5410-229-13P_21

TM-10-5410-229-13P Modular Command Post System (MCPS) Green NSN 5410-01-323-2454 Tan NSN 5410-01-334-7529 Manual
Page Navigation
  3    4    5    6    7  8  9    10    11    12    13  
TM 10-5410-229-13&P 1-10. LOCATION AND DESCRIPTION OF MAJOR PARTS - Cont’d. 1/2" apart.  Corresponding quick disconnect female fasteners are located on  the  opposite  side.    Both  ends  are  secured with  one  each  additional  quick  disconnect  male/female  fastener,  as  well  as  2"  strips  of  hook  and  pile  fasteners.    One carrying handle is located at each end of the bag.  A label with abbreviated frame set up instructions is sewn to the inside of the bag.   An  identification  label  is  also  sewn  to  the  inside  of  the  bag.    Additionally,  "FRAME  BAG"  and  a  weight  limit warning are stenciled onto the side.  One frame transport bag is issued with each MCPS. (13) Fabric Transport Bag.  The fabric transport bag (13) is constructed of a coated cloth material.  When loaded, it  is  approximately  36"  long,  26"  wide  and  15"  high.    Three  quick  disconnect  male  fasteners  are  located  along  one  side approximately 14" apart.  Corresponding quick disconnect female fasteners are located on the opposite side.  Both ends are  secured  with  one  each  additional  quick  disconnect  male/female  fastener,  as  well  as  2"  strips  of  hook  and  pile fasteners.  One carrying handle is located at each end of the bag.  An identification label is sewn to the inside of the bag. Additionally, "TENT BAG" and a weight limit warning is stenciled onto the side.  Two fabric transport bags are issued with each MCPS. (14) Tent Pin Container.  The tent pin container (14) is constructed of a polyester cloth.  It is approximately 37 1/2" long and 15 1/2" wide.  The container is secured with tie straps.  One tent pin container is issued with each MCPS. b. Tent  Frame  Assembly.    The  major  components  of  the  tent  frame  assembly  are  identified  in  Figure  1-2,  and described in paragraphs (1) through (3) below. (1) Telescopic Pole Assemblies.  The telescopic pole assemblies (1) are constructed of aluminum alloy tubing. They support the covered entrance way.  The upper part fits through grommets located in the entrance way roof assembly. The poles also fit through two pole holders on the left and right blackout door assemblies.  Two telescopic pole assemblies are provided with each MCPS frame assembly. (2) End  Wall  Frame  Assembly.    The  end  wall  frame  assembly  (2)  is  constructed  of  extruded  aluminum  tubing and  supports  the  front  or  rear  of  the  MCPS.    It  consists  of  two  upper  (3)  and  two  lower  (4)  leg  assemblies,  two  rafter assemblies  (5),  two  end  wall  fitting  assemblies  (6),  an  end  peak  fitting  assembly  (7),  a  left  hand  purlin  (8),  a  cable assembly (9), and a cord (10).  Two end wall frame assemblies (2) are required to set up the MCPS. 1-8







Western Governors University

Privacy Statement
Press Release
Contact

© Copyright Integrated Publishing, Inc.. All Rights Reserved. Design by Strategico.