TM 10-5410-221-24
1
Screw (2)
17
Rivet (34)
33 Closeout
49
Washer (10)
2
Washer (2)
18
Angle
34 Blind nut (10)
50
Lockwasher (10)
3
Rivet (25)
19
Closeout
35 Screw
51
Rivet (23)
4
Rivet (56)
20
Rivnut
36 Rivnut
52
Strap
5
Screw (2)
21
Screw (2)
37 Adapter frame, R.H.
53
Closeout
6
Blind nut (2)
22
Washer (2)
38 Adapter frame, L.H.
54
Rivnut
7
Screw (4)
23
Ground rod
39 Rivet (6)
55
Screw (2)
8
Blind nut (4)
24
Blind nut
40 Angle
56
Washer (2)
9
Hinge assembly
25
Rivet (44)
41 Closeout
57
Ground rod
10
Closeout
26
Angle
42 Angle
58
Rivet (24)
11
Seal, bulb and tail
27
Seal
43 Closeout
59
Handle assembly
12
Rivet (58)
28
Closeout
44 Box
60
Closeout
13
Thermal strip
29
Rivet (66)
45 Tee, upper
61
Removable panel
14
Screw (2)
30
Rivet (66)
46 Seal, bulb and tail
15
Blind nut assembly (2)
31
Tee
47 End panel assembly
16
Hinge assembly
32
Seal, bulb and tail
48 Screw (10)
Figure 10-5 - Continued
(9) Remove rivet (35) to remove handle
assembly (36) and shims (37, 38) from panel.
(Located in back of manual)
c. Disassembly. Disassembly the folding floor
(10) Remove velstat floor covering (39) from
panel facing by peeling from cemented area per
as a guide and observing the following.
d. Repair. Repair damage to honeycomb panel
(1) Remove rivet (5) and screw (6) t remove
hinge half (7) from panel edge. Re move seal (10) by
straighten any bent plates, latches, angles, or extrusions
using hammer, pliers, vise or other suitable tool.
(2) Remove rivet (8) and retainer strip (9) and
e. Overhaul. Overhaul the folding floor panel
remove seal (10) from panel edge
assembly as required to return to a serviceable condition
(3) Remove screw (11) and remove bellows
frame (12). Remove screw (13) bracket and spacer
f. Assembly. Assemble the folding roof panel in
(16). Remove insert (14 by drilling using a drill bit with
the same diameter as the insert.
(4) Remove bellows frame (18, 19) b.
guide and observing the following.
removing screws (17).
(1) Cement seals (10, fig.
(5) Remove keeper plate (21) by re moving
screws (20).
(2) Replace velstat flooring (39), apply-ing the
(6) Remove rivets (22) and remove gasket
one part adhesive from the repair kit -to both the floor
retainers (23, 24, 25). Remove bulb seal (26) by sliding
facing and back of' velstat cover. Clean bonding area
from gasket retainer groove per detail A.
thoroughly to as-sure all old adhesive residue is
(7) Remove inserts (27, 28) by drilling using a
removed. Care-fully position velstat cover along one
drill bit with the same diameter as the insert, and remove
edge of panel and work toward the opposite edge using
doubler (29, 30).
a hand roller or other suitable tool to work out any
(8) Remove bolt (31), washer (32) and ring
wrinkles or air bubbles.
assembly (34) from panel. Disassemble ring assembly
(3) Replace potted inserts using procedure
(34) from plate by removing pin. Remove insert (33)
from panel by drilling out with a drill bit having the same
(4) Replace bulb seal assemblies (26) by
diameter as the insert.
coating bottom edge with one part adhesive from repair
kit and sliding into groove in gasket retainers (23, 24,
25).
10-13