TM 10-5410-221-14/1
(1) Remove screws (17, fig. 6-7, sheet 1 of 5) from
washers (106) to secure circuit breaker to panel, and
terminals and disconnect electrical leads.
position circuit breaker in a straight line to rear of panel
(2) Remove screws (99, fig. 6-7, sheet5 of 5) and
(123).
washers (100) and circuit breakers (101).
(2) Install the screws(17, fig. 6-7, sheet 1 of 5)to the
c. Installation. Install circuit breakers (101, fig. 6-7,
terminals and connect electrical leads to circuit breaker.
sheet 5 of 5) using figure 6-7 as a guide and observing
the following:
(1) Position circuit breakers on panel and secure with
screws (99) and washers (100).
a. General. Circuit breaker(110, fig. 6-7, sheet5 of
(2) Connect wire and terminal assemblies.
5) provides protection against damage resulting from an
overload in the sump pump receptacle. The circuit
breaker opens the receptacle in the event the load
reaches 3 amps. Opening of the circuit breaker is
a. General. Circuit breakers provide protection
indicated by the extension of the reset button. The circuit
breaker is reset by pressing in on the reset button.
against damage resulting from an overload in the interior
b. Removal.
(1) Remove the screws from the terminals and
breakers open at 20 amperes. Opening of the circuit
disconnect electrical leads from circuit breaker (110, fig.
breakers is indicated by the extension of the reset
button. The circuit breakers are reset by pressing in on
(2) Remove nuts (108) and washers (109) used to
the reset button.
b. Removal.
secure circuit breaker (110) to panel, and remove by
pulling from rear of panel (123).
(1) Remove the screws (17, fig. 6-7, sheet 1 of 5)
c. Installation. Install circuit breaker as follows: (1)
from the terminals and disconnect electrical leads.
Install nuts (108, fig. 6-7, sheet 5 of 5) and washers
(2) Remove nuts (102, fig. 6-7, sheet 5 of 5) and
(109) to secure circuit breaker (110) to panel and install
washers (103) used to secure circuit breakers (104) to
to rear of panel (123).
panel (123).
c. Installation. Install circuit breakers using figure 6-
(2) Install the screws to the terminals and connect
electrical leads to circuit breaker (110).
7 as a guide and install as follows:
(1) Install nuts (102, fig. 6-7, sheet 5 of 5) and
washers (103) to secure circuit breakers (104) to panel
(123).
(2) Install screws(17, fig. 6-7, sheet 1 of 5)to the
a. General. Circuit breaker (113) (fig. 6-7, sheet 5
terminals and connect electrical leads.
of 5) provides protection against damage resulting for an
overload in the air lock light receptacle. The circuit
breaker (113) opens the receptacle in the event the load
reaches 25 amps. Opening of the circuit breaker is
indicated by the extension of the reset button. The circuit
a. General. Circuit breaker (107, fig. 6-7, sheet 5 of
breaker is reset by pressing in on the reset button.
5) provides protection against damage resulting from an
b. Removal.
overload in the humidifier receptacle. The circuit breaker
(1) Remove the screws(17)(fig. 6-7, sheet 1 of 5)
opens the receptacle on the event the load reaches 10
from the terminals and disconnect electrical leads.
amps. Opening of the circuit breaker is indicated by the
(2) Remove nuts (111, fig. 6-7, sheet 5 of 5) and
extension of the reset button. The circuit breaker is reset
washers (112) used to secure circuit breaker(113) to
by pressing in on the reset button.
panel, and remove by pulling from rear of panel (123).
b. Removal.
c. Installation. Install circuit breaker as follows:
(1) Remove the screws (17, fig. 6-7, sheet 1 of 5)
(1) Install nuts (111, fig. 6-7, sheet 5 of 5) and
from the terminals and disconnect electrical leads from
washers (112) to secure circuit breaker (113) to panel,
circuit breaker.
and install by positioning to the rear of panel (123).
(2) Remove nuts (105, fig. 6-7, sheet 5 of 5) and
(2) Install the screws(17, fig. 6-7, sheet 1 of 5) to the
washers (106) used to secure circuit breaker(107) to
terminals and connect electrical leads.
panel, and pull circuit breaker in a straight line from rear
of panel (123).
c. Installation. Install circuit breaker as follows:
(1) Install nuts (105, fig. 6-7, sheet 5 of 5) and
6-43